Metals -> Structural steel -> Alloy structurall steel Characteristics of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ).
Material : 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) Substitute: 40ÕÔÀ, 35ÕÌ, 40ÕÍ, 25ÕÃÑÀ, 35ÕÃÑÀ Classification : Alloy structurall steel
Chemical composition in % of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) . C Si Mn Ni S P Cr Cu 0.28 - 0.34 0.9 - 1.2 0.8 - 1.1 max 0.3 max 0.025 max 0.025 0.8 - 1.1 max 0.3
Temperature of critical points of the grade 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ).
Ac1 = 760 , Ac3 (Acm ) = 830 , Ar3 (Arcm ) = 705 , Ar1 = 670 , Mn = 352
Mechanical properties under Ò=20o Ñ of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) .
Assortment Dimension Direct. s â s T
d 5
y KCU Heat treatment - mm - MPa MPa % % kJ / m2 - Bar Æ 25 1080 830 10 45 490 Guenching 880o C, oil, Drawing 540o C, water, Sheet annealed 500-750 14
Brinell hardness of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) (annealing) , HB 10 -1 = 229 MPa
Physical properties of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) . T E 10- 5 a 10 6 l r C R 10 9 Grade MPa 1/Grade Watt/(m·Grade) kg/m3 J/(kg·Grade) Ohm·m 20 2.15 38 7850 210 100 2.11 11.7 38 7830 496 200 2.03 12.3 37 7800 504 300 1.96 12.9 37 7760 512 400 1.84 13.4 36 7730 533 500 1.73 13.7 34 7700 554 600 1.64 14 33 7670 584 700 1.43 14.3 31 622 800 1.25 12.9 30 693 T E 10- 5 a 10 6 l r C R 10 9
Technological properties of the material 30KHGSÀ ( 30HGSÀ, 30ÕÃÑÀ ) . Weldability: limited weldability. Flakes : predisposed Temper brittleness: predisposed
Specification :
Mechanical properties : s â - Tensile strength , [MPa] s T - Yield stress, [MPa] d 5 - Specific elongation at fracture , [ % ] y - Reduction of area , [ % ] KCU - Impact strength , [ kJ / m2 ] HB - Brinell hardness , [MPa]
Physical properties : T - Test temperature , [Grade] E - Young modulus , [MPa] a - Coefficient of linear expansion
(range 20o - T ) , [1/Grade] l - Termal (heat) condition coefficient , [Watt/(m·Grade)] r - Density , [kg/m3 ] C - Specific heat
( range 20o - T ), [J/(kg·Grade)] R - Electrical resistance , [Ohm·m]
Weldability : without limitations - welding is done without heating and subsequent heat treeting limited weldability - welding is possible under heating up to 100-120 grade and subsequent heat treeting hard weldability - obtaining the quality welding needs the additional operations:heating up to 200-300 grade; the heat treeting ia annealing
Top
© 2003 - 2009 All rights reserved. About program.
Èíôîðìàöèÿ âçÿòà ñ ñàéòà Ìàðî÷íèê ñòàëè è ñïëàâîâ
© 2002 - 2009 Ìîññïåöñòàëü. Âñå ïðàâà çàùèùåíû
