Metals -> Bronze -> Wrought tin bronzes Characteristics of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ).
Material : BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) Classification : Wrought tin bronzes
Chemical composition in % of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) . Fe Si P Al Cu Pb Sb Bi Sn Impurity max 0.02 max 0.002 0.2 - 0.3 max 0.002 95.6 - 96.3 max 0.02 max 0.002 max 0.002 3.5 - 4 all 0.1
Comment: Cu is a basis; the percentage of Cu is given approximately. Mechanical properties under Ò=20o Ñ of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) .
Assortment Dimension Direct. s â s T
d 5
y KCU Heat treatment - mm - MPa MPa % % kJ / m2 - soft 300-380 40-58 hard 500-700 6-10
Brinell hardness of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) , soft HB 10 -1 = 55 - 70 MPa Brinell hardness of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) , hard HB 10 -1 = 160 - 170 MPa
Physical properties of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) . T E 10- 5 a 10 6 l r C R 10 9 Grade MPa 1/Grade Watt/(m·Grade) kg/m3 J/(kg·Grade) Ohm·m 20 1 84 8900 90 100 17.6
Technological properties of the material BrOF4-0.25 ( BrOF4-0.25, ÁðÎÔ4-0.25 ) . Melting temperature, °C : 1060 Forging temperature,°C : 700 - 800 Annealing temperature, °C : 600 - 650
Specification :
Mechanical properties : s â - Tensile strength , [MPa] s T - Yield stress, [MPa] d 5 - Specific elongation at fracture , [ % ] y - Reduction of area , [ % ] KCU - Impact strength , [ kJ / m2 ] HB - Brinell hardness , [MPa]
Physical properties : T - Test temperature , [Grade] E - Young modulus , [MPa] a - Coefficient of linear expansion
(range 20o - T ) , [1/Grade] l - Termal (heat) condition coefficient , [Watt/(m·Grade)] r - Density , [kg/m3 ] C - Specific heat
( range 20o - T ), [J/(kg·Grade)] R - Electrical resistance , [Ohm·m]
Top
© 2003 - 2009 All rights reserved. About program.
Èíôîðìàöèÿ âçÿòà ñ ñàéòà Ìàðî÷íèê ñòàëè è ñïëàâîâ
© 2002 - 2009 Ìîññïåöñòàëü. Âñå ïðàâà çàùèùåíû
